How to Safely Clean Diamond Rings at Home
RelationshipThe little secrets of sparkling jewelry:
When looking at my diamond the top looks shiny and shiny, however on the sides it gets a bit dirty. Like any expensive diamond ring that is worth a lot, it has a guarantee that includes regular cleaning services. So I used it once. I went straight to the diamond exchange, waiting in line, taking photos, asking for identification and a very long story just to write here.
A diamond expert in a jewelry store, told me a secret, you don’t have to run to the store to clean the sparkling and shiny ring, you can do it yourself at home.
Unlike silver, gold does not acquire a dull, stained finish over time. However, gold can still collect dirt in everyday use. To restore the brilliance of precious gold diamond rings, bracelets, necklaces, and other jewelry, you can do the following:
1-Cleaning jewelry with soap:
Pour a few drops of dishwashing liquid into a bowl or cup of warm (not boiling) water and mix gently. Running tap water will work, but for best results you can use sparkling water. Do not use boiling water, especially if the jewelry contains gemstones and fractures like opal stones that can crack due to rapid and extreme temperature changes.
Soak the gold jewelry in a solution for about 15 minutes. During the soak, hot water and soap will get into the cracks and crevices and remove dirt that is difficult to remove by hand.
Take off the jewelry and gently scrub it with a toothbrush. Scrub each piece individually, paying special attention to hidden corners where dirt can hide. Use a very soft brush, the softer the better. The stiff bristles can scratch the surface of the jewelry. If the jewelry is coated with gold (as opposed to pure gold), the especially hard bristles can even remove the golden layer completely. Special brushes designed for this purpose are the best, but most soft and smooth brushes (like brow brushes) will work too.
Then wash each piece under warm running water. Additional washing under running water will help remove any dirt that has not been caught on the brush. Again, make sure the water is not too hot. If the jewelry is washed in the sink, be sure to put something in to block the drain. This way, you won’t accidentally lose your jewelry if it falls out of your hands. Alternatively, you can wash the jewelry in a colander.
Finally, dry the jewelry with a soft cloth and allow it to dry on a towel in the open air before wearing it again. If the jewelry is still wet, it will form a moisture trap for the skin, which can lead to irritation.
2- Cleaning jewelry with toothpaste:
Mix a small amount of toothpaste with water (for every inch of toothpaste in a bowl or palm, mix a tablespoon or two of water to make the paste). Toothpaste is good for removing accumulated dirt from gold jewelry without scratching it. This cleaning method does not use the jewelry and can therefore be used frequently, for quick cleaning, or when no other cleaners are available.
Scrub the toothpaste mixture gently with a soft bristle brush. If there are scratches on the jewelry, it is probably from the toothbrush and not the ointment. Use a brush that is as soft as possible. Alternatively, you can simply rub in toothpaste undiluted with water. But this method can be more difficult to clean in small cracks in the jewelry.
Finally, wash the jewelry well to remove accumulated dirt.
3- Using boiling water:
As mentioned above, one should know when it is appropriate to clean in boiling water. Pure gold can be boiled without problems. However, boiling delicate gemstones (such as higher clarity diamonds, opal, pearls, coral, and clear stones) can crack and destroy them. Especially if the jewelry is at a cold temperature before boiling. Boiling is also not good for gem-attached jewelry, as it can release the glue. If the goal is to clean pure gold jewelry or gold jewelry with “strong” gemstones (such as diamonds, not clarity-enhanced diamonds), cleaning with boiling water is an excellent option.
It is not necessary to boil a lot of water to “drown” all the jewelry. You can boil them in a small pot over gas or other water-safe tools (such as a mug, Pyrex bowl, or metal container). ). It is important to ensure that the jewels are not placed on top of each other because the water must be able to reach any jewel. So make sure the tool is the correct size.
Wait for the water to cool down. When you can put your hands in the water, it’s time to remove your jewelry. Scrub each piece with a soft brush, then pat dry with a soft towel and allow to air dry completely.
Don’t be alarmed if the water looks dirty – it’s a good sign! When boiling water releases dirt that has accumulated on jewelry, it can float to the surface of the water. The appearance of dirty water, promising clean jewelry!